|
Hollow Silver Bead
Why a project on a simple thing like doming a silver bead? Maybe it’s not so simple. If you shy away from making beads, perhaps this project will get you back on track. It details the steps for making a 3/8" round 24-gauge silver bead from two 1/2" discs by using a dapping block and punches. A dapping block is usually a cube or flat rectangular block of brass or steel in which various half-sphere impressions, called “dies,” are cut. Dapping punches are cylindrical steel rods with a spherical bulb on one end. Half-sphere die impressions and spherical dapping punches range in size from 2mm to 50.8mm (2"). Die sizes are not marked on the block, but the diameter of the punch sphere is stamped in millimeters on the shank. The final dome size is made from the 9.5mm (3/8") in the dapping block. The final size of the bead must conform to the size of the final die so that you can shape the two half-domes to fit exactly together. The correct size disc is essential in order to form the desired size bead. If the disc is not large enough, the complete half-sphere cannot be reached without excessive thinning; if the disc is oversized, the disc can easily be damaged at the die rim as well as become stuck in the die well before the final size is attained. For this bead we will form two 1/2" discs cut from 24-gauge metal and form them up to 9.5mm. |
| Step by Step |
|
|||||||||||
|
Locate the 9.5mm die as the final size for a 1/2" disc, and back up 4 larger sizes in sequence to start the first punch at die #1.
|
||||||||||||
|
With the torch, heat the dome just until the solder tacks up to the sides of the dome. Cool the dome, then swipe the dome rim ledge across the 320-grit sandpaper to remove solder from the ledge but still maintain the rough surface. When soldering the two domes together, you don’t want the domes to “float” on melting solder and slide out of alignment. Instead, the solder on the sides of the dome follows the torch heat and moves through the joint by capillary action.
Dip both cleaned domes in liquid flux and (bead hole side down) allow most of the flux to drain off. Use fine-tipped tweezers to pick up the domes. Thread 2" or so of uncoated 22-gauge straight steel floral wire, first through the tack-soldered dome, then through the other dome and poke the wire through a hole in the honeycomb block. The floral wire provides some support, but gravity holds the domes together. Gently tap the domes down and into perfect alignment over each other.
Hand Finish. Use 400-grit, 600-grit, 1200-grit, and 4000-grit polishing papers (WetorDry®Tri-Mlte® from Rio Grande), or rub the bead with wet pumice powder, to refine the surface to a scratch-free satin finish. Use a rouge polishing cloth for a final shine. Machine Finish. Refine the surface with 400-grit 3M™ Radial Bristle Discs. Use a tripoli-charged buffing wheel, followed by a rouge-charged leather buffing wheel. Remove the compounds with diluted ammonia or use an ultrasonic cleaner. Rotary Tumbler. Use green-fine plastic media in distilled water and deburring compound for 4 to 6 hours, followed by 4 hours of mixed stainless steel shot (minus the straight pins) in distilled water and burnishing compound. Stop to admire your work and imagine the possibilities: add texture, mix metals, inlay, pierce or stamp designs on beads, solder wire twists on top of finished beads, add domes to other design projects. Using described techniques, you can make 5, 10 or 100 beads. But first, try a number of different dome sizes to see which sizes work the best for you with your tools. This project originally appeared in Doming Silver Beads: Step-By-Step Instructions for Making Your Own Silver Beads, written by Nancy Howland, and reprinted here with her permission. |
||||||||||||
|
________________________________________________________________ Cool
Tools | Feature
Stories & Artist Profiles | Projects
& Workshops | Technique
Articles | Business
Articles | News,
Conferences, & Deadlines | Subscribe
to JA Flashcard eNewsletter
Articles & Workshops | Bead Fest | Jewelry Classes | Jewelry Show Guide Show Calendar | Search for Products & Suppliers | Classified Ad Deals | Advertising Rates & Information | Store - Books & Back Issues | Contact Us | Links | Site Map
About Us | Subscribe to Lapidary Journal Jewelry Artist | Subscription Customer Service/Account Lookup Contact
us |
Round discs.
Drill.
Dome. 
At die #1, use a 9mm dapping punch and hammer straight down on the bead hole to the die center bottom.
Move to die #2 and, with the 9mm dapping punch, hammer straight down the center.
At die #3, change to a 7mm dapping tool. This time, the partial dome likely sits slightly above the die rim. Hammer the punch straight down on the center bead hole. Stay centered on the disc and the die so that the disc edge will scrape past the die rim without creasing or cutting the metal.
At die #4, your dome also will sit slightly above the die rim. Use the 7mm dapping punch to hammer straight down centered over the bead hole and die. At this point, your dome should have reduced from 12.7mm (the 1/2" you started with) to 10.3mm in diameter, with a height of about 4.5mm. The dome shape at this stage is a rounded cone.
Anneal the two domes before the next doming step. After annealing, go to die #4 and use a 6mm dapping tool to lightly hammer the punch down once on the bead hole to slightly harden the metal (which prevents further stretching) and to firmly establish the center point of the dome.
Move the dome to die #5 — the goal 9.5mm die. Change back to the 7mm dapping punch. At this stage, the dome sits high above the die rim. When the angle of the dome wall to the die rim is at least 45°, the dome will scrape past the die rim without being cut. If the dome is too shallow to the die rim (more than 10.3mm in diameter), back up to the next larger die and use a 7mm punch to hammer midway on the dome — north, south, east, and west — to curl the dome wall inward.
Use the 7mm punch and start with a lighter hammer blow to partway move the center of the dome down — then another hammer blow to about midway — then a third hammer blow to the base of the die. This three-step gradual hammering allows you to adjust as you go to stay centered on the dome. Any off-center hammer blow will crease or cut the dome against the die rim.
Now that the dome center is seated inside die #5, change to an 8mm dapping punch. Hammer straight down with considerable force. This hammer blow widens the base and arc of the dome, plus adds some height. If the hammer blow is too light, the dome likely will not attain enough height and will be stuck in the die. If it is stuck, use a 6mm dapping punch to hammer halfway down the dome sides and up to about 1mm below the dome rim. The dome wall will curl inward and free the dome from the die block.
Tilt the dome in die #5 so that the dome rim is as close as possible to the die center to prevent creasing the dome edges on the die rim. Use the 8mm dapping punch to hammer all along the dome wall to round out the dome to a perfect half-sphere.
Use calipers to measure the dome height. The height must be slightly higher than one half of the diameter, or at least 4.9mm, so that there will be enough extra metal to allow the dome rims to be sanded flat.
Sand.
Solder.
Place a chunk of honeycomb soldering board on top of a flat soldering pad over pumice in a rotating annealing pan.
Initially keep the torch at least 5" away; rotate the annealing pan and slowly warm the bead until the flux dries out and powders along the solder line. Direct the torch to the lower dome so that evaporating water escapes as air through the top bead hole before dried flux closes this hole. If this warming process is rushed, the flux will vigorously bubble up and push the domes out of alignment. If this happens, remove the bead to pickle, rinse, flux, and start again.
When the flux shows white powdering at the solder line, move the torch in quickly. Rotate the soldering board arrangement and direct the torch to a point just below the rim of the lower dome. The bead will heat up very quickly and solder “all at once.”
Air-cool the soldered bead and remove the steel wire. Pickle and rinse in water. Use a flux dispenser bottle to insert water (or baking soda and water) into the bead to flush out acid. Drain on paper towels.
Sand and Polish.
Use a 1" x 2" rectangle of 320-grit silicon carbide sanding paper to sand excess solder from the soldered joint, to remove lumps of solder left over from tack-soldering, and to remove any flaws on the bead surface. As you move in sequence from course to fine, always sand in the same direction.
Further refine the surface with rectangular pieces of 400-grit, then 600-grit sanding paper.
Depending on your equipment, three options for a final finish are:
